Is it possible to stain tile

Tile painting is an excellent, quick, and low-cost way to freshen up tile in the short-term. But tile replacement is always the best option for long-term durability. Apply the stain to the tiles using a tile sponge cut down into a manageable-sized piece.

Soak up some stain on the sponge and wipe it onto the tile. If you are creating a pattern or using multiple stains , tap or dab the sponge against the tile to apply each color, letting the stain dry between colors. Ceramic tile refinishing can be used on most any tile surface, but you should consider how the surface is going to be used and how much wear and tear it will receive.

Bathroom floors can be refinished but it is not advisable to refinish tile entryways where abrasive grit can damage the floors. Most ceramic tiles can be painted , as long as it's not frequently subjected to water or heavy wear. For instance, you can paint tiles on a bathroom wall, but avoid painting tiles that line a bathtub, shower, or that is on the floor or a countertop.

Repair chips, cracks and other surface damage before painting. Many porcelain tiles can be resurfaced and recolored to match your new decor at a very small cost compared to replacement. Clean the tile to be recolored with a mild detergent like Tide and rinse thoroughly. Allow the tile and grout to dry completely before continuing with the project. Porcelain Tile Makeup Additionally, porcelain tile is tougher, more scratch resistant than other varieties, and more durable and resistant to stains.

It's possible, but I can 't speak to how washable the whitewash will be. The whitewash will stick to the tile. Be sure to read ALL of my whitewash columns here at my site. Especially the one with the secret recipe in it. If your old ceramic tile is worn or dated, you can lay new tile right over the old, and avoid the huge job of tearing out the old tile. This assumes that the floor underneath is solid concrete and that there are no cracks in the existing tile indicating underlying problems in the concrete.

Steps Work out how much stain or paint you will need. Measure the area that you want to cover in sections. Use masking tape on areas that you want to avoid. The tiles need to be as clean as possible to receive the stain and have it result in an even color.

Let the tiles dry completely. Apply a coat of primer to any nonporous tiles. Paint the primer on using a paintbrush, carefully covering each tile right up to its edge. Let the primer dry until it is no longer tacky to the touch. Apply the stain to the tiles using a tile sponge cut down into a manageable-sized piece. Soak up some stain on the sponge and wipe it onto the tile. After about 6 hours your paint should be completely dry.

Now give the paint a light sanding using grit sandpaper. Remove any excess dust using a towel. At this time you should apply a 2nd coat of paint. Continue using a zig-zag paint application finishing with a top to bottom motion with the paint roller to ensure a smoth finish. It may take up to a week after painting for your tile paint to completely cure. This risk includes when you paint ceramic tile too. To avoid a paint job that does more harm than good, invest in options like enamel, latex, or acrylic latex paints.

Remember, these paints should only be applied after a primer is applied and fully dried. This way, the paint will bond to the surface properly. Your email address will not be published. Follow us Facebook Twitter Pinterest. Search Search for: Search. I am in the same boat. My entire house of door and window trim, base board and crown molding are all a beautiful stained medium brown tone to match the hardwood floors.

I could not possibly paint, nor do I want to, all the door and window molding in the entire house; I want to leave the door and window trim stained. What should I do with the base boards? Should I paint the crown molding white in the adjacent addition which has 9 foot ceilings or leave it stained?

Please help!! Keep the cabinets as they sound nice and replace the counter tops with the light color like : 1. Granite Counters Granite is the countertop material of choice when there are no other things to think about - like money. It defines elegance in a kitchen. As the use of granite becomes more widespread, the price comes down. The beauty of the stone contributes to the beauty of even the most modest kitchen. Pros: holds up to heat; comes in a range of almost colors; looks permanent and substantial; will last a lifetime; new sealers are almost maintenance-free; 2nd highest hardness rating after diamonds; has a high value to home buyers.

Cons: expensive, but becoming more affordable; requires some maintenance; some stones absorbs stains if not sealed; knives can become dull if you cut on it; can crack if stressed or improperly installed. It is available in a larger range of colors than granite and has a nonporous surface that resists scratches.

It's easy to maintain, without the annual sealing required by natural stone. Pros: Resistant to stain and acid; easy care. Cons: Expensive. Solid Surface Because solid surface counters are just what they're called, solid, any scratches can be sanded out. The countertops are custom-made to your specifications by companies such as Avonite, Corian, and Swanstone.

Pros: comes in a rainbow of colors and patterns; seamless; stain resistant. Cons vulnerable to hot pans and stains which can damage the surface; can be moderately expensive. Ceramic Tile Ceramic tile is durable and easy to clean.

Add to that inexpensive and you've got a really good choice for countertops for the average home. Because it's installed a section at a time, it can be done by most resourceful homeowners. Pros: takes hot pans; easy to clean; wide range of price, color, texture and design.

Cons: counter surface is uneven; tiles can easily chip or crack; grout lines become stained; custom-designed tiles are very expensive. Laminates Laminate counters bear trademarks such as Formica, Nevamar, and Wilsonart.

They're made of plastic-coated synthetics with a smooth surface that's easy to clean. The pieces are cut to size and finished on the ends.